Tip 1: How to treat neck dress

If you know how to sew dresses, surely you do not just wondering how to execute and handle neck different styles of dresses sewn by different patterns and techniques.Beautifully and carefully looks treatment of the neck and armhole dress in a single cut piping - handle neck this way is very convenient if you sew a dress-box.
Guide
1
Sew in a dress zipper, cream dress details and try on it to make sure that the dress sewn correctly before treating neck.On the shoulder seams baster, remove them to stay open.The side sections of the dress and treat sostrochite on a typewriter.
2
carve out single cut piping shaped neck and armholes of your dress.The width of the facings should be 4 cm without seam allowance to be added in addition to the total width of the piping.
3
carve out the basic fabric piping with allowances and dublerin adhesive fleece or cut out without seam allowance, just by the standards of the neck and armholes.Duplicate parts Dublerin facings using the iron.
4
Make a single item for pre-dresses and two pieces for processing back.The side seams on the piping sostrochite on a typewriter, and then iron the iron joints on the product and piping.Fold the front side of the piping together with the dress, carefully align the armholes, neck and neck forehand back to the relevant parts of facings and make a small mark on the 3 cm from the shoulder seams.
5
Baste piping with details of the dress, stopping baster on the previously made marks, then the inside of the back bend braid dress zipper and baste the neck.Baste the piping to the band lightning, before reaching the seam stitch, and then on a typewriter prostrochite neck and armholes dresses, also dwelling on the labels of the shoulder joints.
6
Stitch neck back so that the line of zipper remained inside.At the upper edge of the zipper, as well as in places of rounding Divide the seam allowances and remove the piping on the front side.Then iron on the wrong side of the cut, and then pull out the piping inside the shoulder cuts, while capturing details of the dress sections of piping and components.Put them together, sour cream and Stitch.
7
then iron shoulder slices, remove the front of the dress and sew exposed armhole.Shape the piping and cut off the excess allowances.Secure the piping inside namitka accurate.Processing neck finished.

Tip 2: How to treat neck bias binding

Processing neck bias binding - one of the most convenient techniques in sewing as plastic and stretching the texture of the tape allows even inexperienced seamstress you arrange complex shape bends products.
How to treat neck bias binding
Guide
1
Get a sufficient amount of bias binding or make it yourself.To do this, cut on the bias tape long 3-4 cm wide, Sew them by putting slices diagonally, straighten the edge in different directions.Mark the middle of the entire length, fold and otutyuzhte.
2
retreat from one end of the bias binding 0.5-1 cm, fold it inwards otutyuzhte.This region will begin.
3
Place oblique Bakey on the back side of the product to be processed, so that its front side is adjacent to the wrong side of the fabric.Align the edge of the neck with a bent end Bakey.Route basting stitch along the entire length of the treated area.The edges of the product on the shoulder seams must be spread in different directions.When the neck will remain until the end of 2-3 cm, cut inlay with a margin of 0.5-1 cm, fold the remainder inside, finish basting, fasten thread.
4
Remove Bakey, to be located overlapping with respect to the front side of the product.
5
Fold about 0.5-1 cm long cut from the inlay inside, route Basting seam on the front side.Try to keep the belt width on both sides was the same, it's easier for you to work on the sewing machine, and the product will look neater.
6
Use a sewing machine.The face of the basting seam route the usual line.Hide the ends.Remove basting.
7
Carefully sew both sides of the fold bias binding on both sides of the neck.If the wrong side line did not pass on the edge of the tape, it will catch a few stitches.If the machine seam gone too deep inside, and the edge Bakey can unbend and expose slice unpicked better detail and do everything over again, as gently mask error with a conventional needle out.
8
If you use a high-quality oblique Bakey with ironed creases, you can immediately put it on the neck so that it covers the edge of the product, and pave a basting stitch from the right side, and then duplicate it on a typewriter.
Sources:
  • as the inlay process
Sources:
  • how to treat neck