Tip 1: How to fill the bobbin

How to fill the bobbin thread?On this issue facing all novice seamstress, even those that are already more or less confidently filled in the upper thread.Meanwhile, it is the correct location of the shuttle often depends on whether the machine sew at all.
you need
  • Sewing machine
  • Shuttle
  • spool
  • Threads
Guide
1
Wind the thread on the bobbin .This can be done both manually and on the sewing machine.Manual - simply wrap the thread turn to turn.Try to do it smoothly, without loops and knots.The bottom panel of the sewing machine has a special pin, the same as the one on which you installed the coil.Put it bobbin .Unwind some thread from the spool and wrap them in a spool.It is necessary that the thread for mechanical winding from slipping.Then turn the flywheel.In this case, the thread is wound on the spool and the needle holder remains stationary.Turn the knob or press the pedal of the machine.Make sure the spool spun in the same direction in which you already started to wind the thr
ead.
2
Tear off or cut the thread.Remove the spool from the pin.The flywheel put in a starting position.Raise the needle bar to its highest position.
3
Take the shuttle.It can be horizontal and vertical, but run by his almost equally.Consider the shuttle.You will see that from the outside it has an oblique slot, covered by a metal plate, but inside - pin.On pin put bobbin .The direction of winding the thread must match the direction of the slot, otherwise the thread will be torn, and the spool quickly jump out of the shuttle.Insert the thread into the slot, and pull it a little bit.It should move freely.
4
At the bottom of the shuttle from the outside, you will see another spike.Take a look at the shuttle.There you will see a groove which is shaped like the projection into the groove.Slightly push the basal plate of the shuttle so that he entered into the shuttle.If the shuttle got right - you clicks.
5
Now we need to pull out the bobbin thread.This is done with the help of the upper thread that you have, of course, have filled and inserted a needle.Raise the presser foot.Lower the needle holder with a needle by turning the knob or pressing the pedal.The bobbin thread must cling to the top and climb out to form a small loop.Pull the loop and pull the thread a little bit.

Tip 2: How to fill in the shuttle thread

while sewing on a sewing machine for many people is a creative pastime, which was nice to escape from the daily household problems.To start sewing, you need to learn not only to perform a variety of joints, but also on their own to cope with a sewing machine, including, and fill it dates of your thread.
How to fill in the shuttle thread
Guide
1
Look at the back of the frame when the presser foot is lowered, raise it and lock the lever in the top position.
2
Before you thread the hook, you must first, pushing the sliding plate, pull the bobbin case out of the car and pull out the bobbin.Wind the bobbin thread color you need, use for it on the machine reel.The thread in the thread guide hole from top to bottom, and then clockwise between the washers and the thread tension dial to the left, passing it successively through the hole of the thread guide.Manually wound around the bobbin a few turns of thread, pull the thread on the spindle.It is easy to click onto the spindle and between the walls of the bobbin will stop, then bring the car in motion and automatically starts a thread wound on the bobbin.Once you have successfully wound on the bobbin thread, start installing the bobbin into the bobbin case.
3
Put on the rod hook pin with wound on her thread and thread the end of the thread into the slot in the shuttle away from you.Pull the thread under the leaf spring, and bring out.
4
Turn bobbin case an angle of 90 °, pull the padlock plate, wearing a bobbin on the bobbin holder rod.When you insert the bobbin on the bobbin in place, hold it with your finger or fasten thread - otherwise the bobbin may be unwound.
5
Check the tightness of closing padlock and make sure that the string does not come under the plate.If the thread gets under the pressure plate, and you do not notice it right away, you will find it immediately when you start sewing - a thread will be made with difficulty and may break off.If you felt that the thread tension was excessive, remove the spool and turn it so that the thread has come under pressure plate.
Helpful Hint
before pulling up the bobbin thread, check whether the needle is inserted.