Tip 1: How to build a pool table

Billiards - a very interesting game of chance and, develops coordination, the ability to feel the force of impact, good eye.If your house is enough space to accommodate (the best solution would be a separate room 4x5 meters), be sure to buy or make yourself table for billiards.
you need
  • - Particleboard (chipboard) with a thickness of 20-25 mm;
  • - plywood or particle board thickness of 3-20 mm;
  • - board 10 mm;
  • - timber 30h25 mm;
  • - Rubber band width 28-30 mm;
  • - decorative fabric;
  • - lining fabric;
  • - wire 2 mm;
  • - net;
  • - Jig;
  • - Drill;
  • - screwdriver or a screwdriver;
  • - file;
  • - furniture stapler;
  • - adhesive;
  • - fasteners.
Guide
1
from a large sheet of chipboard do table eshnitsu for table well.Plate must be perfectly smooth.Workpiece dimensions 1050h535 mm.Corners cut off the base of the workpiece at an angle 45⁰, 50 mm at each end, cover their plates.
2
In the center of the long side pockets cut holes 45 mm long and 40 mm deep.From the bar make the legs: their length s
hould be equal to 100 mm, the edge angle spilite 45⁰.Secure them with screws in the corners of the table and so that they lay parallel to the plates.
3
top of a sheet of MDF or plywood 3-20 mm.Mark the middle of the table well and cut a rectangular hole pockets: 45 mm wide and 20 mm deep.In the corners of the hole should be done at an angle 45⁰, depth (measured from the angle) of 30 mm, a width of 45 mm.The surfaces of the grooves treat a file.
4
of a board thickness of 10 mm Saw trims the following sizes: 4 strips of 445 mm and 2 strips of 510 mm.Put on the edge of the 10 mm Cut the corners under 45⁰.From bar 30 x25 mm make the board: 2 pieces of 515 mm and 4 pieces of 450 mm.On the narrow side aside from the edge of 10 mm, and just as at the Cut the strips at the corners 45⁰.Details grind and coat with varnish.
5
rubber 2-3 mm thick, cut a strip width of 28-30 mm in length boards.Lubricate the end of the nail and glue to one end of carnations.Pass the strip through the entire board, a little stretch and fix the other end of the board.From decorative fabric (the same as the table cloth eshnitsy) cut a strip width of 40 mm and a bead wrap with rubber lock at the bottom of the furniture stapler.
6
Each pocket saw out of plywood bracket, drill the holes for fastening.Cover part varnish.From wire 2 mm bend the staples of the same shape, they will be hidden under the veneer.To attach the wire mesh of the bags.
7
Collect table for billiards of cooked items. plywood table eshnitsu arrived at the base of chipboard, lay on top of the backing, and decorative fabrics.To avoid wrinkles, lubricate the surface of the adhesive, and then lock the fabric stapled by bending the edge of approximately 10 mm.
8
Set side by screwing them with screws.Carefully vymeryat all distances are square and level gauge.Lubricate bead glue and fix them trims.Check if the ball enters the pocket, if it is bad - somewhat expand it.
9
Place the bracket-trim on the pocket and mark the holes with an awl centers.Then remove it and attach the staples with grids.Close the pocket escutcheon.Perform a test of self-made billiard table well.

Tip 2: How to make a billiard

To achieve success in the championship game of billiards in the , require daily intensive training.Also, sometimes you just want to play a game or two with friends.However, a good billiard table is not cheap.If possible get it you do not, do yourself a pool.
How to make a pool
you need
  • - wooden blocks of varying lengths;
  • - a sheet of plywood or particle board;
  • - lining fabric;
  • - green cloth;
  • - glue "Moment";
  • - rubber band;
  • - screws;
  • - nails;
  • - billet aluminum brackets;
  • - metal wire;
  • - ready for mesh pockets;
  • - billiard balls;
  • - furniture lacquer;
  • - hacksaw, file, chisel;
  • - skin;
  • - round cue stick.
Guide
1
manufacturing billiard tables - painstaking work, but can cope with it even the person who has not mastered the art of cabinetry.All materials can be purchased at stores that sell furniture of residues and waste production.Do not use raw wood, accurately measure the size before sawing off and cut the workpiece.Take your time.Even with careful decoration items you do the job for three or four days.
2
Tackle basis for a billiard table.For it will need solid and perfectly aligned bars.Treat them with a file and trim cloth.The length of the longitudinal bar is 1005 mm, fixing and longitudinal - 532 mm.Put them together with glue and fluff the edges styanuv screws.The finished base has the form of the frame.Dry harvesting.Cut hacksaw edge angle of 45 degrees.Fabricate legs and attach them with glue and screws.Coat all parts with two or three layers of lacquer.
3
Select material for tabletops.This may be plywood or chipboard of 600 to 1000 mm.Remove irregularities of a saw and polish the workpiece cloth.Mark the contours on the sheet countertops and cut grooves with a chisel and a hacksaw.Strip slots file.
4
Deal trims.Take the prepared bars, saw off corners, lining size.Strip the joints, treat the surface with a file and sandpaper details.Similarly finished and the board.Finished parts cover varnish in two or three layers, well prosushivaya each.
5
Cut a rubber band equal to the length and width of the board of 30 mm.Its the end of the grease glue, attach to the edge of the board and nail two nails.Pull the strip along the side and secure it at the other end the same way.Cut a strip of fabric, and it obtyanite board previously smeared with glue.Fold the edges missed their extra portion of the glue and tucked the ends of the rubber gasket inside.Secure it with two nails.
6
Fabricate 4 corners and 2 side braces from plywood and aluminum plates (best to use the appropriate size ready).Need and staples.The ends of the wire sharpen file.
7
assembling the product pool.Nail the countertop to the bottom of the table.Cut a piece of lining fabric of 600 to 1,020 mm.Carefully glue promazhte countertop, including the side part.Stick to the surface of the lining, carefully smoothing the folds of his hands.The edges of the fabric bend under the table top.Cut a piece of decorative trim size of 610 to 1030 mm.Place it on a table and fold.Along the edges of the fabric promazhte glue and tuck under the table top on 10 mm.Secure the trim nails.
8
Install sides and pockets.Pre-need to drill into the side holes for screws.Place the first long, and after a short side and secure with screws so that the heads do not protrude above the surface.On the outside of the boards the adhesive glue and nail trims their nails.To attach luzam ready grid.Secure them with a plywood braces and aluminum plates and screw the screws.Check whether the cue ball is pocketed.
9
Make a cue from a round stick with a diameter of about 25 mm.Planed it in the form of a cone, ensuring straightness of lines.Treat cue sandpaper and varnish coat in two or three layers.At the end of the stick a piece of felt.Make strips of an equilateral triangle, affixed with glue and small nails.Oshkurte it and cover with varnish.Triangle is needed for a smooth putting some balls on the field.