Tip 1: How to insert a string into a guitar

It is sad, but the strings - consumables, they tend to break, stretch, deform, etc.Therefore, every self-respecting guitarist shall always have with you a set of spare strings, and should be able to install them correctly.Quite often the musicians complain about their tools, because they quickly become frustrated, blaming the poor quality of the guitar or musical accessories.In fact, most of the blame for improper installation strings.
you need
  • new set of strings that is appropriate for your guitar and meets your needs (training, composing, etc.)
Guide
1
Loosen the old string with the help ofKolkova mechanism.Loosen need pretty strong, but that the string is not much slack.This is done in order to change the strength of the sharp tension does not occur distortion of the guitar fretboard.
2
Unwind after a while chopping and remove the old string.Then untie the strings from the nut.But do not remove all the strings at once - can be difficult, and visualize the sample in the form of
a stretched string it will be gone.
3
Secure the new string on thresholds, and then bring it to the headstock, conceding the hole chopping.Note that you must leave a margin for winding on the peg the string.Then string be careful to pull in the direction of the headstock.Be careful - do not dёrgayte string in different directions, because it can deform or break that, of course, is highly undesirable.
4
Fold the end of the string in the direction of the center of the headstock and pass right under the string.As a result of these actions is to turn the lock.Due to the retention of the string under tension prevent its deformation and to facilitate the overall process of its installation.
5
start spinning peg holding string under tension.With this wrap the string itself zazhmёt.If you need to increase the oblique angle of the string with respect to the nut, then wrap the string chopping down the shaft rather than up.After all, if the slope angle is very small, string can come off the nut during the game.
6
Pull the rest of the string, based on a sample in the form of a tight first.This method of installation allows you to string a long time not to get upset instrument.

Tip 2: How to insert a string

For those who have decided to learn to play guitar without a hitch, it is recommended to use nylon strings .These softer metal and do not lead to fatigue when playing finger.Correct installation of the nylon string sound will bring harmony and softness in sound reproduction.
How to insert the string
Guide
1
Remove the old string , weakening their tension.The hinges are located on the screw chopping, pry some sharp object and pull the ends of the strings from the holes in the drum.Do not be embarrassed if neck of the guitar will begin to fluctuate after the removal of the strings.This is typical of the instrument, the neck of which is held on the screw.After setting the string returns to a stable position.
2
order not to disturb the sequence of arrangement of strings, begin setting with the fine (first) string .Make a distance of 1.5-2 cm from one of the endings string bundle, similar to that tie at the end of the thread, start sewing.
3
Attach the string on the stand by following the loop.Guitar while holding horizontally.End with a bundle perekin'te through the stand and move to either side of a string.Then thread the end of the string in a loop.Make sure that the unit was located outside the loop.
4
tighten it to prevent it blossomed.For this the index finger from the hole for the string press the intersection with loop end strings to the stand.String always keep taut.Pull free hand over the opposite end of the string , tightening it.
5
Sit down and put the guitar on the floor.To secure the cord was taut, and was not able to be dismissed on the stand, push it right knee to the neck.End thread the string through the hole, which is located on the roller chopping, print it on a couple of centimeters.
6
Screw string on roller chopping.Remember that all strings have to twist in the same direction.Make a few turns overlap.One of them has to go across all the others.
7
fingers of his right hand, pull the string, holding it at a right angle to the neck and not letting loose.Continue to wind the string on the platen.When she is finally tightened, check the loop on the stand: libertine string can not hold the line, so all you need to rewrite.
8
Installation bass strings (4,5,6) nodules can do.Note that at one end of the string bass has a fiber loop.To consolidate string it has nothing to do, but most often in a hole in the base string is inserted into the end in which there is no loop.
Note
Before you put metal strings, understand, is whether your guitar for them.Some instruments can not put metal strings, especially after nylon, because the probability of failure of the nut, such unintended tension of such a force.Be careful.
Helpful Hint
Count strings slack so that she made two or three turns around the Colca.Less turns do not - likely dismount strings, and more than three turns to do is simply irrational.
Sources:
  • replacement string classical guitar
  • how to install the strings on a guitar