you need
  • - tape measure;
  • - a large sheet of paper (or a piece of wallpaper Whatman);
  • - line;
  • - pencil;
  • - scissors.
Guide
1
Remove measurements.To construct a pattern of classic trousers you will need: putting the waist, hips and length of putting the product.
2
Start with constructing patterns front of his pants.On a large sheet of paper (it can be a piece of wallpaper or unnecessary Whatman) build a right angle.His top mark the point T. From her aside yardstick down the length of the article, this point mark the letter N.
How to build a pattern of classic trousers
3
Spend H-point perpendicular to the straight line TN right.Put down from the point T 1/2 a measure putting thighs plus 1 cm. The point of the le
tter B. Next, mark the point B to the right aside 1/2 a measure putting thighs plus 0.5 cm, mark the point B1.
4
to postpone construction of the width of the seat to the right of the point B1 1/10 of putting measurements of hips and put the point B2.Swipe up from point B a line parallel to the line of TB at their point of intersection of the label T1.Put the point B1 up a segment equal to the value of the segment B1B2.Connect the points with a smooth line as shown in the drawing pattern.
5
Now draw a line to iron the edges.To do this, the width of the seats (a segment B1B2), divide in half.Then divide by half a segment dividing point to point B and put a point B3.Swipe down and up from the point B3 dotted line parallel to the CN.
6
aside the right of the H-point interval of 4 to 6 cm. Points 4-6 and B connect.From line to iron the edges aside right segment equal to the value of the point to the line 4-6 to iron the edges, and place the point H1.Connect the dots H1 and B2.
7
now proceed to design the waist trousers.Put down from the points T1 1 cm. Connect the dots 1 and T.
8
calculate the depth of darts.To do this, measure the value of the segment T1B1.Subtract the value obtained by putting 1/2 waist measurements.From this difference, subtract 0.5 cm and spread to the front and side and front tuck.For example, the length is 7.5 cm T1B1 therefore 7,5-0,5 = 7 cm, 7 cm / 2 = 3.5 cm. So the depth of the recesses is equal to 3.5 cm.
9
Put the resulting value of the waist to the right of the point T. Arrange tuck smooth line.Further, aside from the line to iron the edges of the right and left half of the value of the depth of the dart (folds) 3.5 / 2 = 1.75 cm.
10
Build pattern back of the pants.To do this, set aside the right of the point B2 1/10 of putting hip measurements plus 3 cm, the point label B4.
11
Divide segment B2B4 half.From the resulting set aside points down to 1 cm. Then, set aside by the waist to the left of the point T1 1/10 of putting measurements of hips and put the point m. Connect the dots and 5.2 m (point T1).
12
bisected interval T1 5.2.Set aside right at a right angle from the points of division 0.5 cm. Connect point T1 0.5, 5.2, B2, 1, B4 smooth line.
13
To issue waistline pants, swipe from the left point T a straight line of arbitrary length.Swipe from the left point T1 line is 1/2 putting waist measurements plus 7 cm, and set point T2.
14
calculate the depth of the rear half of the pants darts.Measure the length of t1t2, subtract from the resulting value of 1/2 putting waist measurements.Spread obtained difference minus 1 cm (the landing) for the two rear tuck in the same way as for the front of the pants.
15
t1t2 Divide cut into three parts.Aside from the division points downwards at a right angle to the line t1t2 10 cm (length tucks) and left and right - 1.5 centimeters (this depth tucks).Then connect point 1.5;10 and 1.5.
16
Through the bottom 1-2 cm aside (of your choice) to the right of the point H1.Connect the dots m2, 1-2 straight line.To obtain a seam line stepper B4,1-2 connect the points.This line is split in half.Aside from the division points at a right angle to the left 3 cm.
17
Connect smooth line point B4, 3, 1-2, as shown in FIG.Pattern-base classic trousers ready.