Tip 1: How to make a subwoofer

How to listen to your favorite music without the speaker ?Why not make the subwoofer with your hands?From listening to the music you get more pleasure, because see the fruit of your labor.
you need
  • - carnations;
  • - wire cutters;
  • - file;
  • - wire;
  • - paper clips;
  • - a hammer;
  • - magnetic tube;
  • - adhesive;
  • - woofer;
  • - chipboard;
  • - a personal computer;
  • - drill with a drill;
  • - plaster on wood;
  • - spatula;
  • - sandpaper;
  • - self-adhesive;
  • - silicone;
  • - wire;
  • - jigsaw.
Guide
1
Bite nail clippers part (leave this part of the nail, which would correspond to the height of the dynamics created ).Then gently file off a file toward the "biting".On the part of the nail, where there is a cap, wrap copper wire with enamel insulation.
2
Make the base: beat hammer usual plain metal clip, with the result that it becomes a small piece of foil.
3
After that, take the magnetic tube, set at its center a nail wound and glue it all to the ground.From the second metal clip make thin, foil
-like, plate and place it on top of the magnetic tube.
4
Connect the speaker and enjoy listening to their favorite music tracks.
5
Collect subwoofer.To buy this for him "heart" - woofer.Then everything is simple: using the program for the calculation of the cut determine the size of the body.This is a very important step, since the correctness of determining the size will depend on the sound quality.Housing Manufacture of chipboard 24 mm thick.Move the subwoofer size and cut chipboard.Then connect the wall of the future of the subwoofer using the self-tapping screws, pre-drill holes have been drilled suitable diameter.For reliability promazhte docking of the glue for wood particleboard.
6
Process the inside of the subwoofer.All internal connecting seams promazhte silicone sealant.Then zashpaklyuyte inner walls of the subwoofer, and then sanded the desired grit and sand wall.Cut a hole jigsaw outlet and phase inverter, as well as to make the body beautiful pen.After the previous procedure obkleyte subwoofer enclosure decorative self-adhesive.Finally, attach the speaker, bass reflex and wire.

Tip 2: How to make the speaker

There are many ways to make the speaker for almost any device and almost all of the materials at hand.We will not describe all the more so for this one article is not enough.We restrict ourselves to two fairly simple ways.
Make the speaker - a simple task
Guide
1
First, choose a nail, think about height approximate size of the speaker.Cut the nail so that you have it was a bit smaller than the projected height of the speaker.Deal with a whetstone or a file clipped the side of the nail.When the surface is smooth and free of burrs wound on this part of the nail cap with copper wire with insulation.But before that you need to do the following: take two buttons clip, break them with a hammer on the anvil, until they become thin as a foil.One of these clips is the base.Now take a nail and glue it to the clip-base.
2
Now take the magnetic tube, which is slightly higher in size than the nail-coil.In this nail and it should go.Glue the pipe to the ground and cover it with a lid of another button, clip and its seal.This speaker is working properly, no squeaks, groans and extraneous sounds.
3
But the way in which you can do the dynamics of coffee cups and old headphones.These speakers are ideal for use with an MP3-player.
4
Take a paper cup, old headphones and scotch tape.At the bottom of the cup on the back of the center mark and cut a hole in it.Attach the headset to the hole circle t his pencil.We need to make a hole slightly smaller diameter.
5
Now insert the earphone into the hole and glue it with adhesive tape or any other tape.Look inside and check that there are no extraneous pieces of cardboard, as well as to the earphone well fitting to the bottom.Otherwise, the sound you will have a rattle.It's all ready speaker.Just do the second speaker.Although the column and comic appearance, but at full volume, they are able to give sound power up to 10-15 decibels.
Note
Be careful when working with a jigsaw.Watch your fingers.
Helpful Hint
If you use self-adhesive under the skin, the subwoofer will look quite stylish.
Sources:
  • subwoofer Putting his hands
  • speaker with your hands