Tip 1: How to tie spokes takes a simple

Beret - thing is so versatile that is suitable for autumn and late spring.It will be combined with the usual jeans and a cocktail dress.This accessory for any occasion you can tie yourself, spending a couple of hours of time and 200 grams of yarn.
you need
  • yarn, knitting needles, needle
Guide
1
for knitting, you will need 200 g of yarn and two sets of spokes - №5,5 and №6.Dial on the spokes 43 №5,5 air loop.The first eight rows of double rubber band beret tie.To do this, alternate, 2-3 facial loop with the same amount backstitches in a row to continue binding on the image to facial hinges located on the right and wrong - on the underside.
2
before proceeding to take the ninth row spokes №6.Main fabric beret dial checkerboard pattern.To do this, tie the three purl loops, then - three facial, then again three purl, etc.Repeat this pattern for three series in the drawing.Then begins a series of three facial, and then knit the three backstitches - and so, too, the three series.After
the pattern repeats itself.At the same time to create a traditional form of beret in the first row 27, gradually add additional loops.Bind this volume to 38 series.
3
Subsequent rows necessary to reduce the width of the beret.For this purpose, 38 and rows 42 to 40 are uniformly remove loops.The forty-sixth row, turn down the number of loops and tie on 20 "checkerboard" 4 more rows.
4
Gently pull spokes and trim operating thread, leaving a segment length of 10 cm. Insert it into the gypsy needle and thread all left open loop.Tighten the tip of the beret, drag the thread on the inside of a hat and fasten the bundle.
5
Ready takes can be decorated with a brooch or decorative buttons.

Tip 2: How to connect a female takes

Beret has become a classic hat.Simple tracery or associated or crocheted, volume and flat, he would decorate a girl with any type of person, but also protects from the cold.
How do I link takes women
you need
  • - 300 g of yarn;
  • - needles № 2,5 and 3;
  • - stocking or circular needles № 2,5 and 3.
Guide
1
Dial on the spokes 80 loops and knit 3-5 cm rubber band 1x1 or 2x2.In order that it is not stretched in the process of socks, elastic knit very tight.
2
knit necessary amount gum, tie one row purl loops on the front side and back elastic knit 1x1 or 2x2.Thus, the rim will double, and therefore cap to surround and heat.
3
in the last row of gum evenly add 45 loops (eventually get 125 loops).Then knit fancy pattern.Note that the number of loops must be divisible rapport pattern.
4
At a height of twenty centimeters knit purl stitch, at the same time to turn down the number of each face first every tenth and eleventh loop and then each sixth and seventh, then a third and a fourth.Finally, every two loop knit together.The remaining loops pull together, fasten thread.
5
Item fold in half and run manually or Stitch seam on the sewing machine.
6
Another way in which the product will seamlessly.To do this you need hosiery needles of the same size.Dial 80 sts on needles hosiery.In the second row distribute them to four (twenty loops on each needle), close the loop in a circle and knit elastic band round the value of three centimeters.
7
Proceed with basic knitting pattern, adding uniformly 16 loops (in the end, you should have the spokes of 96 loops).If you are not comfortable knit fabric on a large hosiery needles, you can go to the circular.
8
Twenty-three centimeters basic pattern, start vyvyazyvayut bedplate.For this purpose the front knit stitch, while performing subtraction in each even row.In the second round knit the two loops together facial, followed by two facial and again two end together, and the two end.Continue to knit in such a way to end the series.Do the same ubavki in the fourth, sixth, eighth and tenth circular row.The remaining pull the loop tight with the help of the working thread.He takes ready.
Sources:
  • just takes