Tip 1: How to sew a dress-transformer

Dress-transformer - it is a model that can be worn in many different ways, each time getting a unique image.It was first demonstrated by journalist and fashion critic Lydia Sylvester in 1976, and after almost 40 years the fashion for these dresses again returned, after only one model, sew that can even novice seamstress can be converted into a chic gala or a casual outfit inevening dress, skirt, tunic tops and even pants.
you need
  • - 3 m of knitted fabrics;
  • - string matching;
  • - a thin elastic band;
  • - sewing accessories;
  • - sewing machine;
  • - Overlock.
Guide
1
To be able to do a variety of problems without drapery, it is recommended to sew a dress-transformer of elastic materials.It is best suited for this purpose sided thin jersey, for example, oil.The size of the cut depends on the desired length of the dress.If you want to make an evening version of the skirt to the floor, you'll need a piece of 1.5 m wide and 3 m long. To dress with a short skirt will need less material.
2
To construct patterns need only two measurements.Measure the waist circumference and the desired length of the skirt.
3
Build pattern skirt.The basis is cut sun.Divide the waist circumference at 6 fold the fabric in four parts so as to obtain a square.From the resulting corner set aside measures and draw an arc.From this line set aside the desired length of the skirt down and spend another arc parallel to the waist.Detail of cut, leaving 1 cm on the hem and seam allowances.
4
to carve out a bodice 2 rectangle length of 1 - 1.5 m and a width of at least 20 cm. The longer these details, the more opportunities for draperies.Carve out a zone.This rectangle is the length equal to the circumference of the waist and the width of 20-30 cm.
5
Sections drawstrings or treat on overlock narrow, tight zigzag stitch.Ties apply at an angle so that they found each other.Apply to this side of the top edge of the skirt and pin pins.
6
Stitch Detail Belt on the short side and across the fold in half so that the seam was inside.Attach the belt to the outlet section of the upper part of the skirt.Cleave all the pins and Stitch on a typewriter.To skirt the best-fitting, apply shear elastic braid and sew her narrow zigzag stitch.
7
Try on dress and adjust the length of the skirt.Cut off the excess.Edge treat overlozhnym seam.Fold the inside out once and Stitch close to the edge.The dress can be worn and drape it in many different ways.
8
skirt to put dress-transformer can be stitched not only flared, and direct style.In this case, you get a great option cocktail dress or outfit for every day.To do this, the pattern pencil skirt.Apply to the cloth, and carve out.Baste all the darts and try on slices and seamy.This must be done in order to skirt a good sitting on your figure.
9
Next Sew all seams.Then iron and sew them to the skirt and belt straps as described above.

Tip 2: How to sew a dress transformer

Behind every beautiful thing, you can go to the trendy shops, but in this case, no one can guarantee you the uniqueness and originality of the new outfit.Today is gaining more and more popularity among the fashionistas dress-up transformer, which is not so difficult to make yourself, but, despite its apparent simplicity, this dress gives you a lot of opportunities to diversify their image.
How to sew a dress transformer
Guide
1
to sew a dress, take a stretch fabric or supplex width of 150 cm.

Build a pattern to get the desired length of the fabric.
2
Measure inch chest, and then measure the girth at several locations - depending on what style you turn the dress, there will be times (waist volume under the breast volume of the breastand neck).The height of the belt should be approximately 15 cm.
3
If you want the dress to the knee-length standard, measure the distance from the knee to the collarbone, and then the lower edge of the waist to the knee.The longer you want the hem - the greater the distance.Next, measure the length of a centimeter from the bottom of the waist to the ankles and waist to ankles from.Based on these yardsticks, determine what the length of fabric needed for sewing.Do not forget about SEAM.
4
Start cutting tissue.
5
to sew the ties, cut from the finished fabric strips 3 cm wide. Stitched one strip to another to form a long strip length of 2-3 meters.Fold the strip inside out, Stitch, treat and remove overlock edge on the front side.
6
For manufacturing belt, cut a rectangle of height 30 cm and a length that you defined for the circumference of the belt.Fold along overlock treat, remove and stitch in the ring.
7
remaining tissue fold along the longest side and the notch in the crook of the fabric on the length of the belt half.Make the cut at the end tuck for sewing belt.Treat cuts overlock and form the back seam.Sew the opening times are prepared for it and treat overlock.
8
Then treat the long edge of the fabric.On the remaining untreated side of the fabric do Drawstring skirt width of 2-3 cm. Drawstring Pass the cooked cross-linked ties and enjoy his own original dress.
How to sew a dress-transformer with their hands
Related article
How to sew a dress-transformer with their hands