Tip 1: How to make a pattern sleeves

Designing clothes every artist faces the need to cut out the sleeves for different items of clothing.Sleeve were cut quite simple, but you need to adhere strictly to the algorithm for constructing such a pattern.
you need
  • -santimetrovaya tape;
  • -karandash;
  • -Paper;
  • -webs.
Guide
1
Try to start to carve out a single-joint sleeve that is suitable for any kind of clothing.To do this, first of all, clear measurements.To begin, measure the length of the sleeves , as well as the length of sleeves up to the elbow.Record data.Next, measure the arm circumference at the shoulder and wrist girth.
2
removing the measurements and using their time to build a drawing pattern, do not forget about a raise.In order to loose-fitting sleeves hand, add about 6-8 cm to measure arm circumference.For a free customized fit to the circumference of the wrist, try to retreat as much as you see fit.It mostly depends on the style of clothing.
3
Begin construction pattern.Take a suitable large sheet
of paper, departing from the left edge of 7-8 cm, and then draw a right angle.Its apex is the point A. Down from that point aside yardstick length sleeves .In place of the end of the straight line set point N. This line - the middle of our sleeves .Next, you need to hold it perpendicular, which will be the bottom of the sleeves .
4
At the bottom line aside bushel wrist girth by adding thereto 2 cm. From the middle of the line set aside equal size in both directions.
5
Then measure the length of the pattern on the armhole product for which we do sleeve.This value divide by 3 and deduct from the result of dividing 2. This result aside from point A on the line down the middle.Spend perpendicular.From the middle of the line again to both sides set aside half of the circumference of the shoulder in each direction.
6
points that you have formed, connected to a point A line that you went after this, divide into four parts.First, divide each half, then divide in half again.
7
front and back of our sleeves best sign to avoid confusion.A point is a point to cut out the middle sleeves .Note that in the process of sewing on it is aligned with the shoulder.

Tip 2: How to build a pattern sleeves

Today in shopping networks, a large selection of books and a variety of other benefits for the design and modeling of clothes.In addition, it is proposed a lot of magazines with ready-made patterns.There are many techniques that are used in the manufacture of patterns.Whatever you have not applied, it is always calculated on a typical figure for the average person.The main thing - it's not even pattern and skill "landing" on the product shape, while taking into account all the individual characteristics.
How to build a pattern sleeves
Guide
1
Take a white sheet of paper A3.Spend on the center of the sheet a horizontal line, set aside about half a perpendicular line.At the intersection point mark, label it, such as "O".Doused sleeves constructed after building armhole products.Observe the relation between the size of the armhole and wide sleeves, which are equal to the width of the armhole = 0.36 x girth shoulder;length = 1.27 x armhole girth shoulder;deep armholes = 0.45 x girth shoulder;doused sleeves height = 0.4 x girth shoulder.
2
aside from a central point "O" up the calculated value doused sleeves, consider the necessary permits for wide sleeves is 2 cm. Put the point of "O1".Width = girth shoulder sleeve + tolerance (for a free fit of 6-8 cm).
3
Divide the value in half and set its value to the left and right of the point "O".Put the point "P" (shelf) and "C" (back).Connect the dots "P" with "O1", "C" with "O1".Divide the segments "PA1" and "DC1" in half, and then another half.
4
wire from point "P" smooth curve to the point of "O1".In the first half of the concave line of 2 cm in the second - curved 1.5 cm. Similarly, for a smooth curve from the point "C" to point "O1".First concave line 1 cm, then 1.5 cm curved.
5
Put sleeve length from the point of "O1" down.Place the point of the "H" (bottom).Left and right of the point "H" at the bottom of the sleeve perform width (coverage wrist + tolerance).Measure the value of the curve "PA1" (doused the front of the sleeve).Compare with the value of the armhole shelves.Measure the value of the curve "CO1" (doused the back of the sleeve).Compare with the value of the back armhole.They must match.If the shelf is less armhole armhole back, doused the front of the sleeve must also be smaller.Measure the difference, divide the number by two and cut a strip of the width of the front of the pattern.Glue this strip to the back of the sleeve.
Sources:
  • Pattern sleeves.